• Switch 1.3.0
• Product Overview
  • Package Contents
  • Technical Specifications
  • Supported SonicWall and third-party SFP and SFP+ Modules
  • Physical Interface - 8 Port Switch
  • Physical Interface - 10 Port Switch
  • Physical Interface - 24 Port Switch
  • Physical Interface - 48 Port Switch
  • Device Management
  • Connecting the Switch to a Network
  • Capacity Matrix
• System Management
  • System
    • Dashboard
    • Network
    • Administration
      • SSH Settings
    • System Information
    • User Management
    • Simple Network Management Protocol
      • Classic diagram of SonicWall Switch for SNMP Testing
      • Add View List
      • Add Target Params
      • Add Target Address
      • Add Notify Setting
      • SNMP Traps/Informs
      • How to configure SNMP on SonicWall Switch
      • SNMP supported OID’s in 1.2.0.1-2s
      • How to Configure SNMP/MIB Browser on Client PC
    • Address Resolution Protocol
      • ARP Table
      • ARP Statistics
    • Authentication
    • Firmware and Settings
    • DHCP Snooping
    • DHCP Relay
    • Time
  • Switching
    • Port Settings
      • Port Settings
        • Native VLAN
      • QoS Settings
        • Bandwidth Control
        • Storm Control
      • PoE
      • Security
        • 802.1X
      • ACL Binding
      • Advanced
    • Spanning Tree Protocol
      • Network Loops
      • Global Settings
      • MST Instance Settings
      • STP Port Statistics
    • Loopback Detection
    • Link Aggregation
      • Port Trunking
      • Link Aggregation Control Protocol Settings
      • Link Aggregation Control Protocol Timeout
      • Trunk Port Settings
    • Port Mirror
    • Jumbo Frames
    • MAC Address Table
      • Dynamic MAC Address
      • Search MAC Address
      • MAC Aging Time
    • Link Layer Discovery Protocol
      • Local Device
      • Remote Device
    • IGMP Snooping
      • Global Settings
      • Group List
      • Router Settings
    • Multicast Filtering
    • Quality of Service
      • Class of Service Mapping
      • IP/DSCP Mapping
      • Advanced Mode
        • Class Mapping
          • Adding a Class Policy
        • Policy Mapping
    • Remote Network Monitoring
      • Stat List
      • Event List
      • Event Log Table
      • Statistics
      • Alarm List
      • History List
      • History Log Table
    • Port Statistics
  • Routing
  • Security
    • 802.1X Security
      • MAC Authentication Bypass
        • Behaviors and Restrictions
      • Global Settings
      • Port Settings
      • Authenticated Host
      • Statistics
    • Denial of Service
    • ACL Management
      • MAC ACL
      • MAC-Based ACE
      • IPv4 ACL
      • IPv4-Based ACE
  • VLAN
    • 802.1Q
      • Configuring IGMP Snooping Settings
      • Configuring DHCP Snooping Status
      • Configuring Access and Trunks using Standalone access
    • Voice VLAN
      • OUI Settings
      • Port Settings
  • Logging
    • Global Settings
      • Local Settings
    • Remote Logging
    • Log Table
  • Diagnostics
    • Ping
    • Trace Route
    • Cable Diagnostics
    • Tech Support Report
• System Maintenance
• Switch Troubleshooting
  • Communication flow between Firewall and Switch before it gets authenticated
• SonicWall Support
  • About This Document

Physical Interface - 48 Port Switch

1. RJ45 Console Port
2. Power LED: Light Off = Power Off; Solid Light = Power On.
3. Fault LED: Light Off = Normal Behavior; Solid Light = Error.
4. PoE Max LED: Light Off = Power Available; Solid Light = Power Exceeded.
5. LAN LED: Light Off = Not activated; Solid Light = Activated.
6. PoE LED: Light Off = Not activated; Solid Light = Activated.
7. LED Selector: Press to change between LAN and PoE LED monitoring.
8. Reset Button: Press to reset the device to factory default settings.
9. RJ45 LAN Ports: 10/100/1000 Mbps or 1 Gbps.

10. LAN Mode LED (Per RJ45 Port): Light Off = No Link; Solid Amber Light = 100 Mbps Link Active.

11. Link/Act LED (Per RJ45 Port): Light Off = No Link; Solid Light = Link Active; Blinking Light = Actively Transmitting / Receiving.

12. Speed LED (Per SFP Port). Solid Amber Light indicates 10 Gbps Link, Solid Green Light indicates 1 Gbps link.

13. Link/Act LED (Per SFP Port).

14. SFP Ports: Small Form-factor Pluggable ports: 1 or 10 Gbps ports.

15. Power Connector.