SonicOS 7 System
- SonicOS 7
- Interfaces
- About Interfaces
- Interface Settings IPv4
- Adding Virtual Interfaces
- Configuring Routed Mode
- Enabling Bandwidth Management on an Interface
- Configuring Interfaces in Transparent IP Mode (Splice L3 Subnet)
- Configuring Wireless Interfaces
- Configuring WAN Interfaces
- Configuring Tunnel Interfaces
- Configuring VPN Tunnel Interfaces
- Configuring Link Aggregation and Port Redundancy
- Configuring One Arm Mode
- Configuring an IPS Sniffer Mode Appliance
- Configuring Security Services (Unified Threat Management)
- Configuring Wire and Tap Mode
- Layer 2 Bridged Mode
- Key Features of SonicOS Layer 2 Bridged Mode
- Key Concepts to Configuring L2 Bridged Mode and Transparent Mode
- Comparing L2 Bridged Mode to Transparent Mode
- Comparison of L2 Bridged Mode to Transparent Mode
- Benefits of Transparent Mode over L2 Bridged Mode
- ARP in Transparent Mode
- VLAN Support in Transparent Mode
- Multiple Subnets in Transparent Mode
- Non-IPv4 Traffic in Transparent Mode
- ARP in L2 Bridged Mode
- VLAN Support in L2 Bridged Mode
- L2 Bridge IP Packet Path
- Multiple Subnets in L2 Bridged Mode
- Non-IPv4 Traffic in L2 Bridged Mode
- L2 Bridge Path Determination
- L2 Bridge Interface Zone Selection
- Sample Topologies
- Configuring Network Interfaces and Activating L2B Mode
- Configuring Layer 2 Bridged Mode
- Asymmetric Routing
- Configuring Interfaces for IPv6
- 31-Bit Network Settings
- PPPoE Unnumbered Interface Support
- Failover & LB
- Neighbor Discovery
- ARP
- MAC IP Anti-Spoof
- Web Proxy
- PortShield Groups
- Static and Transparent Mode
- SonicOS Support of X-Series Switches
- About the X-Series Solution
- Performance Requirements
- Key Features Supported with X-Series Switches
- PortShield Functionality and X-Series Switches
- PoE/PoE+ and SFP/SFP+ Support
- X-Series Solution and SonicPoints
- Managing Extended Switches using GMS
- Extended Switch Global Parameters
- About Links
- Logging and Syslog Support
- Supported Topologies
- Port Graphics
- Port Configuration
- External Switch Configuration
- External Switch Diagnostics
- Configuring PortShield Groups
- VLAN Translation
- IP Helper
- Dynamic Routing
- DHCP Server
- Configuring a DHCP Server
- Configuring Advanced Options
- Configuring DHCP Option Objects
- Configuring DHCP Option Groups
- Configuring a Trusted DHCP Relay Agent Address Group (IPv4 Only)
- Enabling Trusted DHCP Relay Agents
- Configuring IPv4 DHCP Servers for Dynamic Ranges
- Configuring IPv6 DHCP Servers for Dynamic Ranges
- Configuring IPv4 DHCP Static Ranges
- Configuring IPv6 DHCP Static Ranges
- Configuring DHCP Generic Options for DHCP Lease Scopes
- DHCP and IPv6
- Multicast
- Network Monitor
- AWS Configuration
- SonicWall Support
Configuring Security Services (Unified Threat Management)
The settings that you enable in this section control what type of malicious traffic you can detect in IPS Sniffer Mode. Typically, you want to enable at least Intrusion Prevention, but you might also want to enable other Security Services, such as Gateway Anti-Virus or Anti-Spyware.
To enable Security Services, your SonicWall Security Appliance must be licensed for them and the signatures must be downloaded from the SonicWall Data Center. For complete instructions on enabling and configuring Intrusion Prevention, Gateway Anti-Virus, and Anti-Spyware, see the SonicOS Security Services Administration Guide.
- Configuring Logging
- Connecting a Mirrored Switch Port to an IPS Sniffer Mode Interface
- Connecting and Configuring a WAN Interface to the Data Center
Was This Article Helpful?
Help us to improve our support portal