SonicWall SonicPoint ACi: Out of Box Setup

03/26/2020 1,421 People found this article helpful 487,788 Views

Description

Resolution

SonicWall SonicPoint ACi Out of Box Setup Video

Topics Covered:

Out of the Box
Port and LED Descriptions
Power over Ethernet (POE) Injector/Switch Overview
Cabling the SonicPoint
Firewall: SonicOS Firmware Requirements
Configure the Network Interface
Configure the WLAN zone

Out of the Box:
The SonicWall SonicPoint ACi package includes the following:

SonicPoint ACi
Cat5 Ethernet Cable
Ceiling Brackets
Anchor/Screw Kit

Status LEDs:
There is a status LED for lan2, lan1, 5G, 2.4G.
There is also an LED for the tool icon and a power LED all the way to the right that indicates the device booting up and having power.

Power over Ethernet (POE) Injector:

The power over ethernet injector is capable of providing 25 watts of power.The port on the left is your "Data and Power out Port".

This is the Port that you will connect to your SonicPoint LAN1/POE Port

The port on the right is your "Data in Port".

This is the Port that you can connect to your SonicWall WLAN X2 port.

Note: In most cases customers will use this this power over ethernet injector to power their device. However, you can also use a POE capable network switch port as long as it is 802.3at compliant and capable of providing 25 watts of power.
Cabling the SonicPoint:
Start by locating the SonicPoint LAN1/POE port. Connect the LAN1 port to the supplied POE Injector port on the left labelled "DATA & POWER OUT".
Now, locate the SonicWall WLAN X2 port and connect it to the POE Injector port on the right labeled "DATA IN".
Note: This is the standard way for connecting your SonicPoint to your SonicWall device. However, as mentioned previously, A POE capable network switch can be used as an alternative for the POE Injector that is supplied with your devices as long as it is 802.3at compliant.

Firmware Requirements:
To effectively manage your Sonicpoint you will need to use a correct SonicOS version.

The SonicOS 5.9.1 or higher will work.
And the SonicOS 6.2.2 or higher will also work.
SonicPoints must be in the configured in WLAN zone. When SonicPoints are in the WLAN zone they are auto detected and deployed.
Also, The SonicOS auto updates the SonicPoint firmware when needed.

Configure SonicWall Interfaces for Wireless Access:

For the Mode/IP Assignment select "Static IP Mode"

In the IP Address field, type in any private IP address that doesn't interfere with any other interfaces on the appliance.

Next you will have to enter a Subnet Mask. The default is 255.255.255.0.

For the other following fields, you can use the default settings or select any other appropriate settings, and then click OK.

Allow Interface Trust"
Select the checkboxes to enable security services on this zone. Minimally, you would enable:

Gateway Anti- Virus, IPS, and Anti-Spyware.

If your wireless clients are all running SonicWall Client Anti-Virus, select

Enable Client AV Enforcement Service.

On the Guest Services tab:

Optionally configure guest Internet access.
For information about Guest Services, see the SonicOS Administrator's Guide.

On the Wireless tab:

Select Only allow traffic generated by a SonicPoint/SonicPointN to allow only traffic from SonicPoints to enter the WLAN zone interfaces, providing maximum security.

Not Finding Your Answers?

ASK THE COMMUNITY

Was This Article Helpful?

YES NO

SonicWall SonicPoint ACi: Out of Box Setup

Description

Resolution

Related Articles

Categories

Not Finding Your Answers?

Was This Article Helpful?

Article Helpful Form

Article Not Helpful Form

Follow Us

Subscribe to newsletter

Stay In Touch