en-US
search-icon

Category : Management and Reporting

  page 1 of 23 2 3 4 5 6 7 8 9 10... 












icon
Monitoring devices via SNMP using Net Monitor (SNMP)
  Configuring Simple Network Management Protocol (SNMP) This section describes how to configure Simple Network Management Protocol (SNMP) settings for one or more…
Product(s):
Management and Reporting>SonicWall GMS
Last Updated On: 6/27/2017
( 391 users found this article helpful ) 1173 View(s)
icon
Reset the admin password for the System and Application Interface (GMSVP on UMA)
OverviewThe default admin password for the System and Application interfaces is password'. The admin account for the Application Interface is separate from the admin…
Product(s):
Management and Reporting>SonicWall GMS
Last Updated On: 7/26/2017
( 396 users found this article helpful ) 1845 View(s)
icon
How to add SonicWall firewalls to Analyzer
 Adding SonicWall AppliancesTo add a SonicWall appliance using the SonicWall Analyzer management interface, follow these steps: 1. Click the appliance tab that…
Product(s):
Management and Reporting>SonicWall Analyzer
Last Updated On: 7/26/2017
( 399 users found this article helpful ) 1305 View(s)
icon
Analyzer: Syslogs are going to wrong syslogs folder on Analyzer
Problem Definition:We have seen a very common issue where the syslogs start getting converted into .pre and going to bad syslogs folder after summarization. Please find the…
Product(s):
Management and Reporting>SonicWall Analyzer
Last Updated On: 6/27/2017
( 389 users found this article helpful ) 1020 View(s)
icon
How to backup/restore the configuration and data from Analyzer (Windows)
How to create a Backup Snapshot: Login to the system interface of the Analyzer. (http://127.0.0.1/appliance/applianceMainPage) Navigate to System | Backup…
Product(s):
Management and Reporting>SonicWall Analyzer
Last Updated On: 7/26/2017
( 388 users found this article helpful ) 1637 View(s)
icon
How is Browse Time calculated in GMS and Analyzer reports?
It is calculated as follows: (Number Of Pages / Noise Reduction Factor) * Average Browse Time Per Page"Number Of Pages" is the number of hits (response by the web site to…
Product(s):
Management and Reporting>SonicWall Analyzer
Last Updated On: 6/27/2017
( 298 users found this article helpful ) 800 View(s)
icon
How to Create Custom Report on Analyzer and Create a Scheduled Report
Step 1: Login to the Analyzer application interface, set a Filter based on particular User or IP address or Service, provide a name to the filter and save the…
Product(s):
Management and Reporting>SonicWall Analyzer
Last Updated On: 7/28/2017
( 303 users found this article helpful ) 985 View(s)
icon
Syslogs are being placed in BadSyslog folder with .pre extension. Summarizer is not working. No rep
Problem Definition:Syslogs are being placed in BadSyslog folder with .pre extension.The root cause is that the Reporting db is not able to commit transactions that were…
Product(s):
Management and Reporting>SonicWall Analyzer
Last Updated On: 6/27/2017
( 387 users found this article helpful ) 1020 View(s)
icon
How to send scheduled reports by e-mail
Step 1: Login to an application interface of the GMS/Analyzer (ipaddress/sgms). Step 2: Go to Console and configure e-mail settings. Note: If the e-mail account requires…
Product(s):
Management and Reporting>SonicWall Analyzer
Last Updated On: 7/26/2017
( 389 users found this article helpful ) 1141 View(s)
icon
Receiving Alerts regarding Disk Space on GMS/Analyzer Software (Windows) deployments
Step 1:  On the server hard drive where the GMSVP folder is installed, check to see if the following subfolder has more than 50Gb of data:  ...GMSVP/Temp …
Product(s):
Management and Reporting>SonicWall Analyzer
Last Updated On: 6/27/2017
( 388 users found this article helpful ) 1218 View(s)